Setting up Meta Advantage+: structure, budget and when to turn it off

(updated ) 5 min read meta-adsadvantage-plus
Advantage+ is Meta's starting point for sales, lead and app campaigns. What that means for structure and budget, and when to turn Advantage+ off.

Advantage+ is Meta’s default setup for campaigns with the Sales, App promotion or Leads objective: Meta applies AI to your audience, your placements and your budget, and manual settings remain available. If you restrict one of those three too far, Advantage+ is off for that part.

So in every Meta campaign, you choose per part whether to give the system room or draw a line yourself. How the algorithm selects ads under Advantage+ is something I described in my blog post on Meta Andromeda.

From Advantage+ Shopping to Advantage+ Sales

Advantage+ sales campaigns used to be called Advantage+ Shopping Campaigns. According to Meta, the most advanced AI optimizations switch on when your sales campaign uses Advantage+ audience, Advantage+ placements and Advantage+ campaign budget.

Meta reports that advertisers using Advantage+ sales campaigns see an average 9% lower cost per conversion. That figure comes from Meta’s own test: worldwide, across all industries, one week starting December 3, 2024. It’s an average, not a promise for your account.

A campaign with multiple ad sets stays Advantage+ as long as you work with a campaign budget. That lets you run different angles side by side without falling back on a fully manual setup.

When Advantage+ is on or off

Meta shows per part whether Advantage+ is on or off. According to Meta’s own explanation, it works like this:

  • Budget: on with a campaign budget, with one or more ad sets, even if you use spending limits per set. Off if you have multiple ad sets without a campaign budget.
  • Audience: on if you use your audience settings as a suggestion. Usually off if you limit the reach further and uncheck the Use as a suggestion box. A minimum age of up to 25 or excluding a custom audience keeps Advantage+ on.
  • Placements: on with Advantage+ placements. Off as soon as you exclude a placement or turn off mobile or desktop.

Account-level settings don’t count toward that status. So if you don’t ship to every country, or you’re not allowed to advertise to people under a certain age, you set that in your account settings without your campaign losing Advantage+. According to Meta, campaigns in a special ad category and pharmaceutical campaigns may not have access to all Advantage+ features.

The existing customer budget cap no longer exists

Advantage+ sales campaigns used to have an existing customer budget cap: a maximum share of your budget for people who had already bought from you. Meta has removed that setting. You can achieve the same thing manually, in two ways:

  1. New customers only: a campaign with a campaign budget in which you exclude your existing customers with a custom audience, for example your customer list.
  2. A cap on existing customers: a campaign with two ad sets and the same ad creative. The first set targets only your existing customers and gets a maximum spending limit. The second set excludes those same customers and gets the rest of the budget.

With the second route, you limit the reach in the first set to a custom audience, without a suggestion. That usually turns Advantage+ off for that set’s audience. For the growth set, it makes no difference.

Why this matters: existing customers buy again more easily. Without a cap, a large part of your budget can go to repeat purchases. Your results then look good, while you win few new customers.

The learning phase remains the pivot point

According to Meta, an ad set usually exits the learning phase after about 50 results in the week after the last significant edit. For shopping ads, Meta cites a minimum of 17 purchases through your website and 5 through Meta. A significant edit can put a set back into the learning phase. Meta mentions pausing and a different optimization event, audience or ad creative, as well as changes to bid strategy or budget, depending on how large they are. Meta recommends waiting to edit until a set has exited the learning phase, and not changing budgets often.

Decision rules: when I leave Advantage+ on and when I draw a line

  • Budget: campaign budget is my default. I only use a budget per ad set if sets need their own bid strategy or budget scheduling.
  • Number of ad sets: more than one only if each set can reach about 50 results per week and does something different from the rest, such as a different product group or a different audience limit.
  • Audience: I leave suggestions as suggestions. Hard limits, such as age or countries you don’t ship to, go in the account settings.
  • Existing customers: if the goal is growth in new customers, I exclude them or give them their own set with a cap. If it’s about repeat purchases, I leave them in and track new and existing customers separately with audience segments in reporting, as Meta recommends.
  • Placements: I leave Advantage+ placements on. I only exclude a placement if it demonstrably doesn’t fit your brand or product.
  • Edits: not during the learning phase. If something does have to change, I bundle the changes into one go, so the set only relearns once.
  • Tracking: Meta recommends connecting your own marketing data to the ad system. The pixel and the Conversions API both belong in your setup.

Your role shifts from turning knobs to setting boundaries. You decide the goals, the budget limits and the creative angles. The system handles the distribution and the auction.

My advice

See Advantage+ as a partnership in which you set the boundaries. Put limits where your business needs them, leave the rest open and only judge after the learning phase. Then the default works for you.

Want to know whether your Meta account is still built the old, manual way, or already set up for how Advantage+ works? Request a Free Performance Quick Scan, and I’ll take a look with you.

Sources

Want to win back return?

Start with a Quick Scan and find your 3 biggest opportunities.